Non-reinforced elastomer washers TYPE N15 and N20
Used with high pressure N15 and N20 In accordance with AbP (General Building Authority Test Certificate) for load class 2 according to DIN 4141 standard, part 3 under pressure of up to 15 N/mm2 (N15) or 20N/mm2 (n20). Non-reinforced elastomeric washers guarantee a controlled load transfer to the support and prevent horizontal distortions and shortening of the washer caused by shrinkage. They prevent excessive loading of the eccentric and pressure on the edge.
Non-reinforced elastomer washers TYPE CR
Non-reinforced elastomer washers CR according to DIN 4141 standard, part 15/150 for load classes 1 and 2 according to DIN 4141 standard, part 3. Non-reinforced elastomeric washers guarantee controlled load transfer to the support, free rotation of elements on the support, and a radical reduction of horizontal forces.
Feel free to get familiar with all dimensions in the CATALOGUENon-reinforced point elastomer-slide washers Type NEG
Elastomer-slide washers in accordance with AbP (General Building Authority Test Certificate) are intended for all point washers with larger ranges of displacement under pressure of up to 5 N/mm2. Thanks to the ideal selection of slide materials included in the elastomer-slide washer, the friction coefficient is minimized while maintaining the right load transfer. These washers compensate the horizontal displacement of the element supported by the free movement of the slide plate over the surface of the elastomer with PTFE cover.Reinforced point elastomer-slide washers Type B1EG
in accordance with the AbP (General Building Authority Test Certificate) are intended for point support with greater ranges of displacement under pressure of up to 15N/mm2. Due to the ideal selection of materials in accordance to DIN 4141 standard, part 14/140. The washers compensate the horizontal displacement of the supported element by the free movement of the slide plate over the surface of the elastomer with PTFE cover.
Feel free to get familiar with all dimensions in the CATALOGUE
Slide tape washers with an elastomer core Type TDG 27 SZ
They comply with the AbP (General Building Authority Test Certificate). By placing a tape washer with an elastomer core in the centre of the supporting surface, e.g. a wall (the axis of the core must coincide perfectly with the axis of the wall), the load from the supported element, e.g. the ceiling, is transferred to the support ideally along its axis. The washer prevents the formation of cracks resulting from horizontal displacements, protects against excessive load on the edge of the supporting surface, and prevents the formation of cracks caused by tilting the wall.
Permanent tape washers with an elastomer core Type TDG 21 S
They comply with the AbP (General Building Authority Test Certificate) for the centring core. Permanent tape washers with an elastomer core are used to determine a fixed point or in the case of minimal displacements of the supported structures, e.g. ceiling, roof, etc. Changes in length and rotation angle are compensated by deformation of the elastomer core. Due to the axial load transfer to the support, edge loads are avoided and cracks caused by tilting the wall are prevented.
Feel free to get familiar with all dimensions in the CATALOGUE
Slide films TYPE TG1 A + b1 / c1
Slide films Type TG1 A are intended for short span roofs in accordance with the inspection certificate (MPA Hannover). The use of the film ensures that there is no “jamming” of structural elements of the building, which may arise as a result of shrinkage and creep, as well as changes caused by the influence of temperature on the building. These films prevent the formation of cracks caused by tilting the wall. Slide films TYPE TG 1 A + b1 / c1Slide films Type TG 1 A with elastomer laminate are used under pressure of up to 3N/mm2 to separate structural elements, e.g. within the foundation, and to limit their jamming, which may arise as a result of creep and temperature changes of structural elements or as a result of building settling.
Feel free to get familiar with all dimensions in the CATALOGUE
Sound-absorbing washers Type SD/TD 21 SD – Acoustic insulation of stairs, landings and connecting platforms.
SD sound-absorbing washers in accordance with AbP (General Building Authority Test Certificate) are designed to dampen vibrations and sounds in general construction buildings and industrial structures. They are marked by very good resilience. Apart from damping vibrations and sounds, the SD washer guarantee the transfer of loads from the supported elements and protect the edges of adjacent elements from damage. The improvement of acoustic insulation in relation to the use of standard elastomer washers is at least 28 dB (under pressure in the range from 0.1 to 1.0 N/mm2). The best acoustic parameters are obtained under pressure of 0.5 N/mm2 – 34 dB. Feel free to get familiar with all dimensions in the CATALOGUE
